| | |
|
| |
| | |
|
Spa Accessories Spa Air Products Spa Circuit Boards Spa Contactors Spa Control Panels Spa Electrical Spa Equipment Packs Spa Filters Spa Heaters Spa Jets Spa Lights Spa Manuals Spa Motors Spa Ozone Spa Pillows Spa Plumbing Spa Pumps Spa Relays Spa Skimmers Spa Switches Spa Temp Sensors Spa Thermostats/Hi-Limits Spa Thermowells/Drywells Spa TimeClocks Spa Transformers Sundance ® Spas Accessories Sundance ® Spas Blowers Sundance ® Spas Circuit Boards Sundance ® Spas Electrical Sundance ® Spas Filters Sundance ® Flo-Switches Sundance ® Spas Heaters Sundance ® Spas Jets Sundance ® Spas Lights Sundance ® Spas Control Panels Sundance ® Spas Pillows Sundance ® Spas Plumbing Sundance ® Spas Pumps Sundance ® Spas Ozones Sundance ® Spas Timers Sundance ® Part History Sundance ® Tech Help Sundance ® Part Catalog Manufacturer Contact Info Brett Aqualine Spa Error Code
|
6560-852 Flow Switch
|
Item Number: SD6560-852
Manufacturer: Sundance® Spas
Manufacturer Part No: 6560-852
|
Sundance® Spas Flow Switch 6560-852
Details:
-
Replaces the Harwil Q-12DS, Q-12DS50 with 1/2" threads
-
Rated at: 50 Watt Max. Resistive, 10 Watt Inductive (Coil) 120-240 VAC. 5-28 VDC 0.5A DC Switching. 2.5 DC Steady State
-
Does not come with cables
-
3/4" slip x slip T with 1/2" threaded reducer for 1/2" threaded flow switch
-
Has standard spade terminals (2 spade terminals)
-
Can be removed out of the T fitting and installed in existing T fitting on your spa with ½" threads
Used On the Following Sundance® Spas Models:
-
All Sundance® Spas 800/850 Models using the 6500-301 Bypass Heater, up to 5/1999
-
780 Dover, 2008-03/2017
-
Metro and Solo, 2007
-
Caprio, Metro and Solo, 2006
-
780 Lagunas Models, 2005
-
850E Series: Caprio, Metro, Solo
-
All Portofino Models, 2000-2004: Metro, Solo
Used On the Following Jacuzzi® Spas Models:
-
J-315, 2004+
-
J-325, 2004 and 2008+
-
J-310, 2002-2003
Installation:
-
Click here for video instructions on replacing your flow switch
-
The connectors on the Flow Switch are attached to a PC Board connector that is located on the PC Board (usually at the top). There are other wires connected to this plug:
-
Jumper interlock wire, Flow Switch, High Limit sensor, and Temp sensor
-
Remove the pin connector from the board.
-
To remove a sensor or switch wire from the sensor harness connector, insert a paper clip into the slot corresponding with the wire to be removed. This will depress the pin tine, allowing the wire to be pulled from the harness connector.
-
Important! When reinstalling the sensor or switch wire back into the sensor harness connector, make sure the pin tine is lifted (approx. 1/32") prior to inserting the wire. This will ensure the sensor wire locks into the harness connector. Do not over bend the pin tine or it may break off.
Troubleshooting:
More Information:
We're on Facebook! Follow us for instructional videos and more!
*FREE Standard Ground Shipping on this item with a $4.95 handling fee on all orders (Contiguous U.S. Only). Please see our Shipping Policy!
For All Sundance® Spas Flow and Pressure Switches, Click Here!
|
|
|
|